SBC Series Sintered Carbon Block Cartridge Filters are high-end type activated carbon cartridges developed by Hongtek. Sintered carbon block cartridges are made of 100% FDA approved high-quality coconut shell or high- iodine-value activated carbon materials. Hongtek use the world's advanced technology of sintering molding to make sintered CTO carbon block filter cartridges possessing strong adsorption ability and good rigid structure. Sintered carbon block filters can removel chlorine, bad taste and odor, chloramines, fine sediment, organic chemicals and heavy metal with high filtration efficiency. Besides, sintered carbon block filter cartridges are more stable and more reliable, owning longer life than normal Extruded CTO activated carbon water filters.
| Filter Media | High iodine values coconut shell activated carbon |
| Length | 5"(127mm), 9.8"(250mm), 10"(254mm), 20"(508mm) According to customers requirements |
| Inside Diameter | 28mm Special ID can be customized |
| Outside Diameter | 2.55"(65mm) Special OD is accepted |
| Filtration Rating | 5μm |
| End Cap | Polypropylene |
| Outer Wrap | Polypropylene Non-woven fabric |
| Gasket/O-ring | Silicone |
| Netting | Polyethylene |
Available ID & OD Sizes of Bare Sintered Carbon Block
● High flow rate and low drop-out, high filter efficiency and longer service life
● Sintered carbon filters have very large filtration area and super strong adsorption
● Sintered carbon cartridges have many porous and good consistency of performance
● Effectively remove chlorinated compounds, organic matter, bad smell, colors, Vocs and THMS
● 100% FDA approved high-quality coconut shell & high-iodine-value activated carbon materials
● Water Purifier
● Drinking Water
● Plating Industry
● Pre RO Water Filtration
● Industry Water Treatment
● Food & Beverage Industry
Operation Data for Sintered Carbon Block Cartridge Filters
| Maximum Operating Temperature | 80℃(176℉) |
| Max. Differential Pressure | 7.0 bar at 25℃ (100 psi at 77℉) |
| Max.Operation Pressure | 17 bar |
| Recommended Change Out Differential Pressure | 2.1 bar (31 psi) |
Flow Rate of Sintered Carbon Block Cartridge Filters
| OD x Length (Nominal) | Chlorine Taste & Odor Reduction Capacity @ Flow * | Initial △P @ Flow * | Nominal Rating |
| 10" x 2.55" | >5,000 gallons @ 0.75gpm | 2.5 psid @ 1 gpm | 5 μm |
| 20" x 2.55" | >10,000 gallons @ 1gpm | 2.5 psid @ 2 gpm | 5 μm |
| Estimated Capacity based on 2 ppm influent concentration with > 95% reduction | |||
Construction of Sintered Carbon Block Cartridge Filters
 | ● Inner layer has no contaminant and carbon granule leak out ● Outer layer is polypropylene non-woven fabric to filter the impurities & sludge ● Sintered carbon block cartridges are made of high iodine values coconut shell ● A variety of filtration rating to keep high filtration efficiency of remove residual chlorine ● The length size of OD and ID can be manufactured according to customer's requirement ● End cap is made of FDA approved polypropylene material, it is reliably sealing & durable ● O-ring can be made of Silicone, Buna-N, EPDM, high temperature resistant & good sealing |
| SBC | Length | ID | OD | Micron Rating |
SBC Series Sintered Carbon Block Cartridge Filters | 5 = 5"(127mm) | I = 28mm | O = 2.55"(65mm) | 5 = 5μm |
| 9.8 = 9.8"(250mm) | ||||
| 10 = 10"(254mm) | ||||
| 20 = 20"(508mm) |
For Example:
SBC-10-I-O-5
SBC Series Sintered Carbon Block Cartridge Filters - 254mm - 28mm - 65mm - 5μm
Special Sintered Carbon Block Cartridge Filters can be customized, such as special ID, OD, length and end caps etc.
Hongtek Filtration Co., Ltd.
Copyright © Hongtek Filtration Co., Ltd. All Rights Reserved | Sitemap
